Quilting 101: How to Bind a Quilt with the Backing

Quilting 101: How to Bind a Quilt with the Backing

The traditional way to bind a quilt is to cut strips of fabric and create bias binding to sew along the edges of your quilt. However, there are several other methods you can use to bind a quilt. One of the easiest ways is the “self-binding” method. This is where you cut your backing fabric slightly larger than your quilt top and batting so that you can fold the backing onto the top of your quilt to create a nice finish. It’s rather simple, and we’re going to show you how to do it in this post, complete with mitered corners!

Step 1: Trim the Batting and Backing to Size

The self-binding method can be used on any size quilt. We think it is the fastest and easiest way to finish a quilt.

You’ll need to square up your quilt before you begin. It's helpful to have all of your quilt layers the same size. Then, trim the quilt top and batting back one inch all the way around, leaving your backing untouched. One inch is the most common size, but you can do more or less. The important thing is that your measurements are consistent all the way around.

Trim Backing Fabric 1" Larger All the Way Around

Be careful not to cut into your backing fabric when trimming the quilt top and batting. You can fold the backing fabric out of the way or carefully trim on the top. Do whatever makes you feel most comfortable.

Step 2: Double Fold and Pin the Backing

Once your quilt is trimmed, start anywhere and fold the backing fabric halfway towards the edge of your quilt top. It should butt up right along the edge of your quilt top.

Fold Backing Fabric Halfway to Meet Edge of Quilt Top

Press the fold to create a crease and then fold the backing halfway again to encase the edge of your quilt. Your binding will be ½ inch when complete. Pin the double fold in place and continue this folding down the side of your quilt.

Some people like to use a glue stick to hold the folds in place, but we prefer quilt binding clips so we don’t have to worry about gumming up our needle.

Self Binding Double Fold

Step 3: Create Mitered Corners

When you get to a corner, fold the binding into a triangle, butting up to the raw edge on the next side of your quilt top.

Keep the triangle in place as you fold the next side the same way you did for the first side. This will form the mitered corner.

 Folding Mitered Corners

Mitered Corner Fold

You might have to play with the corner a bit to get it just right.

Step 4: Sew the Binding in Place

After the binding is secured with pins or clips, head to your sewing machine to stitch it down. Use a straight stitch or a decorative stitch to attach the binding. We like to stich 1/8 inch in from the folded edge.

Stitch Binding in Place

Use thread that matches or coordinates with your backing fabric. We also recommend using a walking foot to evenly feed all the layers through your machine. If you don’t have this specialty presser foot, you can get a universal one from Love Sew.

When you come to a corner, stop sewing with your needle in the down position and lift your presser foot to pivot to the next side of your quilt. Watch to be sure there are no tucks or puckers when sewing the mitered corners.

Perfect Mitered Corner

And there you have it! See how easy it is to bind a quilt with the backing fabric? We hope you give it a try.

What other quilt tutorials would you like to see? Leave us a comment below.

Don’t forget to also check out all the lovely Quilt Kits at Love Sew!

Reading next

Quilting 101: 5 Quilt Patterns Perfect for Beginners
Quilting 101: The Most Efficient Way to Make Half-Square Triangles

21 comments

Lorraine

Lorraine

I have not done a binding like this before it looks a lot simpler than attaching a binding. I will try it on my next quilt.

Rudine

Rudine

I always have done my binding that way, by doing the corners your way seems to be easier than the way I was doing them!! Thank you

Carolyn Weaver

Carolyn Weaver

A GReat help. Thank you so much!

Jo

Jo

I am new to quilting and confuse myself often, the miter corners are confusing so yours seem a
Lot easier. Thanks for the help.’

Gale

Gale

I have used this edge on several quilts and it makes a great edge every time. Thanks for the clear explanation.

Leave a comment

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.